MGMT 340 Week 4 Course Project Homework & Quiz

MGMT 340 Week 4 Course Project Homework & Quiz

  • MGMT 340 Week 4 Project: Systems Analysis SDLC Phase 2 Package

Petrie’s Electronics Case, Chapter 7
2. Again,  review  the  DFDs  you  developed  for  the Petrie’s Electronics case (or those given to you by your instructor). Use these DFDs to identify the attributes of each of the six entities listed in this case plus any additional entities identified in your answer  to 

Question  1.  Write  an  unambiguous definition  for  each  attribute.  Then,  redraw  PE Figure  7-1 by  placing  the  six  (and  additional) entities  in  this  case  on  the  diagram  along  with their associated attributes
3. Using  your  answer  to  Question  2,  designate which attribute or attributes form the identifier for each entity type. Explain why you chose each identifier
4. Using your answer to 

Question 3, draw the relationships between entity types needed by the system. Remember, a relationship is needed only if the system  wants  data  about  associated  entity  instances. Give a meaningful name to each relationship. Specify cardinalities for each relationship and explain  how  you  decided  on  each  minimum  and maximum cardinality at each end of each relationship. State any assumptions you made if the Petrie’s Electronics  cases  you  have  read  so  far  and  the answers to questions in these cases do not provide the evidence to justify the cardinalities you choose. Redraw your final E-R diagram in Microsoft Visio

  • MGMT 340 Week 4 Problems/Exercises

Chapter 7
5. Consider the E-R diagram in Figure 7-20. Based on this E-R diagram, answer the following questions:
a. How  many  EMPLOYEES  can  work  on  a project?
b. What is the degree of the Used_on relationship?
c. Do any associative entities appear in this diagram? If so, name them.
d. How else could the attribute Skill be modeled?
e. What  attributes  might  be  attached  to  the Works_on relationship?
f. Could  TOOL  be  modeled  as  an  associative entity? Why or why not?
16. The owner of two pizza parlors located in adjacent towns wants to computerize and integrate sales  transactions  and  inventory  management within and between both stores. The point-of-sale component  must  be  easy  to  use  and  flexible enough  to  accommodate  a  variety  of  pricing strategies and coupons. The  inventory management,  which  will  be  linked  to  the  point-of-sale component,  must  also  be  easy  to  use  and  fast. The systems at each store need to be linked so that sales and inventory levels can be determined instantly for each store and for both stores combined. The owner can allocate $40,000 for hardware and $20,000 for software and must have the new system operational in three months. Training must be short and easy. Briefly describe three alternative systems for this situation and explain how each would meet the requirements and constraints.  Are  the requirements  and  constraints realistic? Why or why not?
17. Compare the alternative systems from Problem and Exercise 16 using the weighted approach demonstrated in Figure 7-19. Which system would you recommend? Why? Was the approach taken in this and Problem and Exercise 16 useful even for this relatively small system? Why or why not?

  • MGMT 340 Week 4 : Structuring Systems Requirements – Quiz

  1. Question : (TCO 5)Conceptual data modeling is typically done in parallel with other requirements analysis and structuring steps during
    2. Question : (TCO 5)On an entity-relationship diagram, a rectangle represents a(n)
    3. Question : (TCO 5) Vehicle identification number, color, weight, and horsepower best exemplify
    4. Question : (TCO 5) An attribute that can have more than one value for each entity instance is referred to as
    5. Question : (TCO 5) The number of entity types that participate in a relationship refers to
    6. Question : (TCO 5) A simultaneous relationship among instances of three entity types is a
    7. Question : (TCO 5) A relationship that the data modeler chooses to model as an entity type best defines
    8. Question : (TCO 6) During which of the following steps will you bring the current phase to a close, prepare a report and presentation to management concerning continuation of the project, and get ready to move the project into design?
    9. Question : (TCO 6) Which of the following is a true statement regarding midrange alternatives?
    10. Question : (TCO 6) A good number of alternatives to generate is 

  • January 29, 2018
Click Here to Leave a Comment Below 0 comments

Leave a Reply:

University of Nairobi